轉向右節臂的模鍛工藝與模具設計
- 文件介紹：
- 該文件為 doc 格式，下載需要 1 積分
- 轉向右節臂的模鍛工藝與模具設計目 錄
摘 要....................................................... Ⅳ
ABSTRACT .....................................................Ⅴ
第1章 綜述..................................................1
第 2 章 工藝方案的確定..................................... .6
第3章 錘鍛模設計............................................8
3.1鍛件圖設計......................... .....................8
3.1.1 分模位置......................... .....................8
3.1.2 機械加工余量和鍛件公差......................... .........8
3.1.3 模鍛斜度.......................... ....................8
3.1.4 圓角半徑.......................... ........ ............8
3.1.5 技術條件.......................... ........ ............8
3.2計算毛坯主要參數.......................... ...............9
3.3 確定設備噸位....................... ..................... 9
3.4飛邊槽的確定.............................................10
3.5確定終鍛模膛.......................... ...................10
3.6確定預鍛模膛.......................... ..................11
3.7鍛模鉗口設計................. ........ ........ ...........12
3.8作計算毛坯圖......................... ................... 12
3.9制坯工步的選擇 .......................... ................14
3.10 確定坯料尺寸.......................... .................14
3.11制坯模膛的設計......................................... 15
3.11.1拔長模膛設計 ......................... ..................15
3.11.2滾擠模膛設計 ......................... ..................16
3.12鍛模結構設計..............................................17
3.12.1型槽布置...............................................17
3.12.2鎖扣設計...............................................17
3.12.3確定鍛模基本尺寸........................................18
3.13轉向右節臂模鍛工藝流程 .......................... ........19
第4章 切邊模設計......................... ....................20
4.1 切邊的方式.......................... ......................20
4.2 切邊力計算和壓力機噸位選擇 ................. ..............20
4.3 切邊凹模設計........................ ......................20
4.4 切邊凹模座設計.......................... ..................22
4.5 切邊凸模設計......................... .....................24
4.6凸模夾持器設計.......................... ..................24
4.7 模具閉合高度............................ ..................25
4.8 卸飛邊裝置.............................. ..................26
第5章 校正模設計........................ .....................27
5.1 校正方式.............................. ....................27
5.2 校正模型槽設計.............................. ..............28
第6章 結論......................... ..... .....................30
參考文獻 ................................. ......................31
致 謝........................................................32
附 錄 一 模鍛工藝卡 ......................... ............33
附 錄 二 鍛件三維圖....................... ...............34
附 錄 三 計算毛坯圖.........................................35
附 錄 四 外文翻譯...........................................36
...
熱門關鍵詞： 
